Following on from the db410c conversion to baremetal testing, reuse the
same scripts in the same rack to run 7 db820c boards (#4/8 is failing in
the bootloader for unknown reasons).
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/4177>
This supports powering up the device (using an external tool you
provide based on your particular lab), talking over serial to wait for
the fastboot prompt, and then booting a fastboot image on a target
device.
I was previously relying on LAVA for this, but that ran afoul of
corporate policies related to the AGPL. However, LAVA wasn't doing
too much for us, given that gitlab already has a job scheduler and
tagging and runners. We were spending a lot of engineering on making
the two systems match up, when we can just have gitlab do it directly.
Lightly-reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Tested-by: Marge Bot <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/4076>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/4076>
The debian firmware package doesn't actually contain it, costing us a
minute of boot time waiting for it to show up.
Lightly-reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/4076>
I'm working on moving the db410c CI from docker to LAVA, which means we
get to boot a custom kernel. To do that, we need to enable ARCH_QCOM in
the kernel, save the dtb around, and include abootimg in our container so
that we can generate combined kernel/dtb/ramdisk images for fastboot.
LAVA's fastboot support is unable to pack the overlay into an abootimg
image, just a cpio rootfs. We could flash the cpio rootfs after overlay
addition, but that takes 2 minutes to do, and causes wear on the devices.
Instead, we'll bring up the network at boot and use wget to fetch the
overlay. We'll want network support anyway, so that we can transfer the
failure xmls back to the gitlab job's artifacts at some point.
Since the msm GPU and realtek network firmware increase our payload by
3MB, add in firmware compression so that it doesn't waste as much RAM on
devices not using it.
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Marge Bot <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/3928>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/3928>
The LLVM libraries were a significant fraction of the entire payload
(55M/250M uncompressed) into the initramfs of the test boards, but
LLVM is only used for the draw module used in select/feedback (which
isn't even tested in CI on ARM yet).
Assume that llvmpipe draw is safe enough for ARM given the coverage on
x86, and disable LLVM for these jobs.
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/3928>
LAVA finds a '#' early in boot and races to emit its shell commands.
Apparently for the current boards those serial commands end up getting
buffered such that things work out, but for db410c and db820c, the buffer
is lost and LAVA gets stuck waiting for the prompt. By setting a prompt,
we can delay our commands until we're actually supposed to emit them (and
suppress a complaint from the lava dispatcher that we're using a risky
prompt!)
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/merge_requests/3883>
Use the normal build job to also prepare the artifacts for LAVA jobs.
For that, the build container needs to also build the test suites,
kernel, ramdisk, etc.
Then the build job will place the just-built Mesa in the ramdisk and the
test job can generate a LAVA job and point to those artifacts.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Tested-by: Marge Bot <https://gitlab.freedesktop.org/mesa/mesa/merge_requests/3295>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/merge_requests/3295>
In preparation for testing drivers other than Panfrost in LAVA labs.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
2019-10-06 07:47:41 -07:00
Renamed from src/gallium/drivers/panfrost/ci/create-rootfs.sh (Browse further)
Eric Anholt
Tomeu Vizoso