120 lines
3.1 KiB
Bash
Executable File
120 lines
3.1 KiB
Bash
Executable File
#!/bin/bash
|
|
|
|
# Boot script for devices attached to a PoE switch, using NFS for the root
|
|
# filesystem.
|
|
|
|
# We're run from the root of the repo, make a helper var for our paths
|
|
BM=$CI_PROJECT_DIR/install/bare-metal
|
|
|
|
# Runner config checks
|
|
if [ -z "$BM_SERIAL" ]; then
|
|
echo "Must set BM_SERIAL in your gitlab-runner config.toml [[runners]] environment"
|
|
echo "This is the serial port to listen the device."
|
|
exit 1
|
|
fi
|
|
|
|
if [ -z "$BM_POE_ADDRESS" ]; then
|
|
echo "Must set BM_POE_ADDRESS in your gitlab-runner config.toml [[runners]] environment"
|
|
echo "This is the PoE switch address to connect for powering up/down devices."
|
|
exit 1
|
|
fi
|
|
|
|
if [ -z "$BM_POE_USERNAME" ]; then
|
|
echo "Must set BM_POE_USERNAME in your gitlab-runner config.toml [[runners]] environment"
|
|
echo "This is the PoE switch username."
|
|
exit 1
|
|
fi
|
|
|
|
if [ -z "$BM_POE_PASSWORD" ]; then
|
|
echo "Must set BM_POE_PASSWORD in your gitlab-runner config.toml [[runners]] environment"
|
|
echo "This is the PoE switch password."
|
|
exit 1
|
|
fi
|
|
|
|
if [ -z "$BM_POE_INTERFACE" ]; then
|
|
echo "Must set BM_POE_INTERFACE in your gitlab-runner config.toml [[runners]] environment"
|
|
echo "This is the PoE switch interface where the device is connected."
|
|
exit 1
|
|
fi
|
|
|
|
if [ -z "$BM_POWERUP" ]; then
|
|
echo "Must set BM_POWERUP in your gitlab-runner config.toml [[runners]] environment"
|
|
echo "This is a shell script that should power up the device and begin its boot sequence."
|
|
exit 1
|
|
fi
|
|
|
|
if [ -z "$BM_POWERDOWN" ]; then
|
|
echo "Must set BM_POWERDOWN in your gitlab-runner config.toml [[runners]] environment"
|
|
echo "This is a shell script that should power off the device."
|
|
exit 1
|
|
fi
|
|
|
|
if [ ! -d /nfs ]; then
|
|
echo "NFS rootfs directory needs to be mounted at /nfs by the gitlab runner"
|
|
exit 1
|
|
fi
|
|
|
|
if [ ! -d /tftp ]; then
|
|
echo "TFTP directory for this board needs to be mounted at /tftp by the gitlab runner"
|
|
exit 1
|
|
fi
|
|
|
|
# job config checks
|
|
if [ -z "$BM_ROOTFS" ]; then
|
|
echo "Must set BM_ROOTFS to your board's rootfs directory in the job's variables"
|
|
exit 1
|
|
fi
|
|
|
|
if [ -z "$BM_BOOTFS" ]; then
|
|
echo "Must set /boot files for the TFTP boot in the job's variables"
|
|
exit 1
|
|
fi
|
|
|
|
if [ -z "$BM_CMDLINE" ]; then
|
|
echo "Must set BM_CMDLINE to your board's kernel command line arguments"
|
|
exit 1
|
|
fi
|
|
|
|
set -ex
|
|
|
|
# Clear out any previous run's artifacts.
|
|
rm -rf results/
|
|
mkdir -p results
|
|
|
|
# Create the rootfs in the NFS directory. rm to make sure it's in a pristine
|
|
# state, since it's volume-mounted on the host.
|
|
rsync -a --delete $BM_ROOTFS/ /nfs/
|
|
|
|
[ -z $BM_ROOTFS_EXTRA ] || rsync -a $BM_ROOTFS_EXTRA/ /nfs/
|
|
|
|
mkdir -p /nfs/results
|
|
. $BM/rootfs-setup.sh /nfs
|
|
|
|
rsync -a --delete $BM_BOOTFS/ /tftp/
|
|
|
|
echo "$BM_CMDLINE" > /tftp/cmdline.txt
|
|
|
|
set +e
|
|
ATTEMPTS=2
|
|
while [ $((ATTEMPTS--)) -gt 0 ]; do
|
|
python3 $BM/poe_run.py \
|
|
--dev="$BM_SERIAL" \
|
|
--powerup="$BM_POWERUP" \
|
|
--powerdown="$BM_POWERDOWN" \
|
|
--timeout="${BM_POE_TIMEOUT:-60}"
|
|
ret=$?
|
|
|
|
if [ $ret -eq 2 ]; then
|
|
echo "Did not detect boot sequence, retrying..."
|
|
else
|
|
ATTEMPTS=0
|
|
fi
|
|
done
|
|
set -e
|
|
|
|
# Bring artifacts back from the NFS dir to the build dir where gitlab-runner
|
|
# will look for them.
|
|
cp -Rp /nfs/results/. results/
|
|
|
|
exit $ret
|